Tweet
Lots of work full mod list is as follows
# -Forced Performance RED turbo
# 8cm ported exhaust housing
-38mm Tial external WG
-2.5 inch tubular 02 housing
-CSI 2.3 stroker kit
Wiseco Coated Pistons - 8.8:1 compression ratio
Eagle Rods
Top Line Bearings
Top Line 4g64 Crank
-Black insert solid motor mounts
-2nd Gen Ported Manifold
Tapped for Greddy EGT probe
-Forced Performance Series 2 COMP Intake and Exhaust cam
-Crower Springs and TI retainers
-28x13x2.75 Griffon Core Intercooler
-2.5 Polished Stainless steel Intercooler pipes
-Walbro 255Lph High Pressure Fuel pump
-750cc FIC injectors
-ACT 2600 pressure plate
-Full face street disk
-Fidanza Light weight Alum flywheel
-1g EPROM Ecu
DSM chips Stage 3 EPROM
-S-Afc
-Autometer Cobalt EGT Guage with GreddyProbe
# -Autometer Cobalt Electronic Fuel pressure guage
# -Autometer VDO Boost guage -30-30 ( POS: reads -3 of true reading at all times )
-Maft
3in LS1 Maf
-3 inch Pipe intake with filter
-Aeromotive Fuel Pressure regulator
# -SS Fuel Feed line from fuel filter
# -SS Fuel Return Line
# -SS Oil feed line from oil filter housing to turbo
-Stock Blow off valve
-Transmission
Installed VCE from MachV Motorsports
-Flexlite slimline fan
-Removed Bumper
-Replaced stock seats with black 90 GST seats
-17x8 Zenatti wheels
Yoko 235/45/zr17 Tires
-New Paint job
Current problems, turbo needs to be rebuilt, filter fell off and it sucked in my valve cover breather hose, breaking 3 fins off the compressor wheel, 500$ and the car will run again as it should. The car is in running condition it just needs a turbo. The drive shaft and transfer case is currently out of the car as i grenaded one of them and needed the car so i installed a Viscous coupler eliminator and drove the car with Front wheel drive.
Car comes with the broke xfer and 1 working transfercase. I have a 92 parts transmission also for 120$ if you want it with the car.
looking to get 6000 OBO
leave me a PM or call me at 1 325 370 6042
to find ANY pictures of the car visit www.swdsm.net most of the install was documented fairly well.
# -Forced Performance RED turbo
# 8cm ported exhaust housing
-38mm Tial external WG
-2.5 inch tubular 02 housing
-CSI 2.3 stroker kit
Wiseco Coated Pistons - 8.8:1 compression ratio
Eagle Rods
Top Line Bearings
Top Line 4g64 Crank
-Black insert solid motor mounts
-2nd Gen Ported Manifold
Tapped for Greddy EGT probe
-Forced Performance Series 2 COMP Intake and Exhaust cam
-Crower Springs and TI retainers
-28x13x2.75 Griffon Core Intercooler
-2.5 Polished Stainless steel Intercooler pipes
-Walbro 255Lph High Pressure Fuel pump
-750cc FIC injectors
-ACT 2600 pressure plate
-Full face street disk
-Fidanza Light weight Alum flywheel
-1g EPROM Ecu
DSM chips Stage 3 EPROM
-S-Afc
-Autometer Cobalt EGT Guage with GreddyProbe
# -Autometer Cobalt Electronic Fuel pressure guage
# -Autometer VDO Boost guage -30-30 ( POS: reads -3 of true reading at all times )
-Maft
3in LS1 Maf
-3 inch Pipe intake with filter
-Aeromotive Fuel Pressure regulator
# -SS Fuel Feed line from fuel filter
# -SS Fuel Return Line
# -SS Oil feed line from oil filter housing to turbo
-Stock Blow off valve
-Transmission
Installed VCE from MachV Motorsports
-Flexlite slimline fan
-Removed Bumper
-Replaced stock seats with black 90 GST seats
-17x8 Zenatti wheels
Yoko 235/45/zr17 Tires
-New Paint job
Current problems, turbo needs to be rebuilt, filter fell off and it sucked in my valve cover breather hose, breaking 3 fins off the compressor wheel, 500$ and the car will run again as it should. The car is in running condition it just needs a turbo. The drive shaft and transfer case is currently out of the car as i grenaded one of them and needed the car so i installed a Viscous coupler eliminator and drove the car with Front wheel drive.
Car comes with the broke xfer and 1 working transfercase. I have a 92 parts transmission also for 120$ if you want it with the car.
looking to get 6000 OBO
leave me a PM or call me at 1 325 370 6042
to find ANY pictures of the car visit www.swdsm.net most of the install was documented fairly well.
Comment