Tweet
I might need to sell my unfinished powerdyne kit. It has a brand new never been used satin powerdyne BD11A head unit (the one that RK-Sprot uses in their kit), the bracket for the powerdyne, grooved 6psi pulley, the bracket for the tensioner pulley, pulleys to possibly use for the tensioner, ZZP valve cover breather, and some assorted hardware. The tensioner bracket still needs some work and the main bracket needs to have a weld run down it. I'll also include drawings of the brackets with the kit in case they need to be remade for some reason or another. I'm looking to get $1100 plus shipping for it. I'm pretty well done with modding the six now so I just don't have the drive to finish this anymore.
using the list from Graymans site this is what would be needed.
All the Piping
Hardware for attaching brackets to block
Spacers for said hardware
New belt
FMU and all lines and check valve http://www.fullthrottlev6.com/forums...ad.php?t=28734 http://www.napaonline.com/MasterPage...One+Way+Vacuum
45* male/female 3/8" NPT fitting for oil pressure sender http://www.northerntool.com/webapp/w..._356143_356143
3rd bracket http://home.comcast.net/~grayman99/T...ket-how-to.htm
Some of the extras I already mentioned are
ZZP valve cover breather
6lb grooved pulley
autolight 103 spark plugs
you can check over the list here
http://home.comcast.net/~grayman99/R...-partslist.htm
Also check his whole page before you install it if you buy it
http://home.comcast.net/~grayman99/guide.htm
If there are any questions let me know and I'll try to answer them. This is a great deal if you are at least somewhat handy. I've done a good amount of the hard work required for this.
PICS!
This shows everything that would come in the unfinished kit.
Close up of the pulleys and the tensioner bracket
This shows the bracket mounted to the blower. You can see at the bottom where the bracket would need to be welded. The scarring on the bottom right is from the sheet rubbing against some metal shavings while I was cutting it. The strength of the bracket is still perfect and the marks could be taken out with some polishing.
This shows the ZZP valve cover breather, the correct spark plugs, and the screwed up bracket. This bracket won't bolt up to the blower but can be used to check how things will bolt up to the block before you drill the holes in the good bracket.
using the list from Graymans site this is what would be needed.
All the Piping
Hardware for attaching brackets to block
Spacers for said hardware
New belt
FMU and all lines and check valve http://www.fullthrottlev6.com/forums...ad.php?t=28734 http://www.napaonline.com/MasterPage...One+Way+Vacuum
45* male/female 3/8" NPT fitting for oil pressure sender http://www.northerntool.com/webapp/w..._356143_356143
3rd bracket http://home.comcast.net/~grayman99/T...ket-how-to.htm
Some of the extras I already mentioned are
ZZP valve cover breather
6lb grooved pulley
autolight 103 spark plugs
you can check over the list here
http://home.comcast.net/~grayman99/R...-partslist.htm
Also check his whole page before you install it if you buy it
http://home.comcast.net/~grayman99/guide.htm
If there are any questions let me know and I'll try to answer them. This is a great deal if you are at least somewhat handy. I've done a good amount of the hard work required for this.
PICS!
This shows everything that would come in the unfinished kit.
Close up of the pulleys and the tensioner bracket
This shows the bracket mounted to the blower. You can see at the bottom where the bracket would need to be welded. The scarring on the bottom right is from the sheet rubbing against some metal shavings while I was cutting it. The strength of the bracket is still perfect and the marks could be taken out with some polishing.
This shows the ZZP valve cover breather, the correct spark plugs, and the screwed up bracket. This bracket won't bolt up to the blower but can be used to check how things will bolt up to the block before you drill the holes in the good bracket.
Comment