Welcome to the FirebirdV6.com/CamaroV6.com forums.
You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!
If you have any problems with the registration process or your account login, please contact contact us.
If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
How much was/is everything costing? We had a brief discussion on your car in the FI section. I was wondering what it ran with the stock motor and only the FFF kit (without intercooler). ?
Pretty sweet. How much are you looking to put to the ground after all this?
My goal is 600 + RWHP....
Originally posted by Shirl
How much was/is everything costing? We had a brief discussion on your car in the FI section. I was wondering what it ran with the stock motor and only the FFF kit (without intercooler). ?
Intercooled:
My first runs on 7 PSI (due to the MAF cutout issue) were not great; mostly because it was my first time at the track as well. I ran 13.9 @106 and a 2.43 60ft. After we could tune past the MAF issue, on 12PSI I ran a 13.0 @ 109 and a 2.1 60ft (with 4-6 degrees of KR bad tune). http://www.fquick.com/videos/viewvideo.php?id=215
I can't share the cost but I will tell you it's over 5K. Here's what the new engine is going to look like. You can see every mod in the link below. I copy and pasted the engine below that. http://www.fquick.com/garages/viewvehicle.php?id=930
L32 rods
Diamond Pistons rings and pins
cometic gaskets
ARP Rod Bolts
ARP Main Studs
Comp Cam: 218/218 528/528 114
Comp 918 Valve springs
Comp. Push rods
Titanium retainers
Comp OE lifters
ARP heads studs
Bore
fully ported heads and intakes
Hone
Deck
Install cam bearings freeze plugs and block balance shaft oil hole
Balance crank rods and pistons
Turn crank
160*
65LB Mototron injectors
SLP MAF
Taylor wires
TR-6's
MSD DIS-4 Plus
Patrick 99 NBM Corvette 02 4x4 Metalic Gray Tahoe LS 01 NBM GTP--> For sale 97 Mystic Teal Camaro
Motor current being built by Abbott racing Heads
13.0 @109 2.1 60ft Mods
Intercooled:
My first runs on 7 PSI (due to the MAF cutout issue) were not great; mostly because it was my first time at the track as well. I ran 13.9 @106 and a 2.43 60ft. After we could tune past the MAF issue, on 12PSI I ran a 13.0 @ 109 and a 2.1 60ft (with 4-6 degrees of KR bad tune). http://www.fquick.com/videos/viewvideo.php?id=215
I can't share the cost but I will tell you it's over 5K. Here's what the new engine is going to look like. You can see every mod in the link below. I copy and pasted the engine below that. http://www.fquick.com/garages/viewvehicle.php?id=930
L32 rods
Diamond Pistons rings and pins
cometic gaskets
ARP Rod Bolts
ARP Main Studs
Comp Cam: 218/218 528/528 114
Comp 918 Valve springs
Comp. Push rods
Titanium retainers
Comp OE lifters
ARP heads studs
Bore
fully ported heads and intakes
Hone
Deck
Install cam bearings freeze plugs and block balance shaft oil hole
Balance crank rods and pistons
Turn crank
160*
65LB Mototron injectors
SLP MAF
Taylor wires
TR-6's
MSD DIS-4 Plus
Patrick 99 NBM Corvette 02 4x4 Metalic Gray Tahoe LS 01 NBM GTP--> For sale 97 Mystic Teal Camaro
Motor current being built by Abbott racing Heads
13.0 @109 2.1 60ft Mods
Cool, thanks for the info. And best of luck with the setup! :)
We process personal data about users of our site, through the use of cookies and other technologies, to deliver our services, personalize advertising, and to analyze site activity. We may share certain information about our users with our advertising and analytics partners. For additional details, refer to our Privacy Policy.
By clicking "I AGREE" below, you agree to our Privacy Policy and our personal data processing and cookie practices as described therein. You also acknowledge that this forum may be hosted outside your country and you consent to the collection, storage, and processing of your data in the country where this forum is hosted.
Tweet
Comment