2001 Gen V

[slow6]

http://www.hollandms.com/PHPBB/phpBB...od&image_id=19
sexE

[UDLOSE98]

Re: 2001 Gen V

gtp guys and their engine appearance.....i tell yea

[slow6]

Re: 2001 Gen V

so... its not a PURE Gen V

[UDLOSE98]

Re: 2001 Gen V

im pretty versed (cause of friends) on the gtp so lets see what i spot...

full sized intercooler
PRJ spark wires
aftermarket dog bones
billet fuel logs
northstar tb
maybe 3.0 pulley
strut tower brace
and apparently a gen V swap.

[WishIHad$$$]

Re: 2001 Gen V

I think it looks great. I really like where the coil packs are located, wonder if that's the stock location.

[Fbody3400]

Re: 2001 Gen V

Looks nice

[UDLOSE98]

Re: 2001 Gen V

I think it looks great. I really like where the coil packs are located, wonder if that's the stock location.

it is the stock location, but trust me it makes the rear plugs a pain in the ***.

[slow6]

Re: 2001 Gen V

cant wait to see dan's new videos
this video is just NOT sufficient dan: !!!!!http://s105.photobucket.com/albums/m...t=MOV00788.flv

Those wires are almost a scam lol
If you show them before and after dyno results of their wires being worse compared to stock you can b1tch and they'll send you new ones but they wont be any better lol

unless yours really are completely dead dudd wires. Then they will have to send you new ones!
There would be a revolt!

[Savorybacon]

Re: 2001 Gen V

It's cute, me likey

[Camaro Dom]

Re: 2001 Gen V

northstar tb? those work on our motors or jsut the L67?

[UDLOSE98]

Re: 2001 Gen V

cant wait to see dan's new videos
this video is just NOT sufficient dan: !!!!!http://s105.photobucket.com/albums/m...t=MOV00788.flv

Those wires are almost a scam lol
If you show them before and after dyno results of their wires being worse compared to stock you can b1tch and they'll send you new ones but they wont be any better lol

unless yours really are completely dead dudd wires. Then they will have to send you new ones!
There would be a revolt!

I am gonna go with MSD's for now and worry about that **** later

[UDLOSE98]

Re: 2001 Gen V

northstar tb? those work on our motors or jsut the L67?

and the northstar wont work with our manifolds.

[slow6]

Re: 2001 Gen V

and the northstar wont work with our manifolds.

thats what Dremels / epoxy / JB weld / duct tape is for! ftw! lol
think I might get rid of my TB & maf altogether...

[blown00]

Re: 2001 Gen V

im pretty versed (cause of friends) on the gtp so lets see what i spot...

full sized intercooler
PRJ spark wires
aftermarket dog bones
billet fuel logs
northstar tb
maybe 3.0 pulley
strut tower brace
and apparently a gen V swap.

You're also missing the headers (they appear to be togs)
that pulley is ATLEAST a 2.7 (2.7 and lower requiring machining to snout) but it looks like a 2.55"

otherwise looks good. If it's a 2001 the LIM and GEN3 were swapped. i want genV. eeeeeeeeeeeeeeeeeeeeeeeee

[blown00]

Re: 2001 Gen V

and the northstar wont work with our manifolds.

I'm sure if someone made an adapter plate for you it would fit, even with the angle? But it serves no purpose unless you inlet is machined to at least 75mm