Quick little photo shoot for my graduation photos!

[Unique96Camaro]

Re: Quick little photo shoot for my graduation photos!

It is definitely looking better.

My own taste is that the wing and the lambo doors detract from the look of the car. But that's just my 2 cents - & I did not even have the decency to chip in 2 cents! You decide what you like.

What job will you be doing after graduation (you mentioned working 40 hours)? Do you have plans for further education or specialized trade skills?

Best wishes on your project car.

Well working 40 hours a week or more for about two months should get me the money to finish the turbo build and everything else i want for the car. then i am going to go to either wyotech or uti

And this motor is going to have a huge cam je forged pistons, huge gt45 turbo, built transmission, stall, and i garrenty it willl make over 500hp

[Unique96Camaro]

Re: Quick little photo shoot for my graduation photos!

:rock:

I can just see it now... "Watch this!" Power braking... nail the accelerator, RPM's shoot up... BANG! "Shiiiiiiiit."

When it's done are you going to get it dyno'd? Although it sounds like this build will take longer than Steve's...

and were going to leave the stock rear end in while im building one and eithier swap it in when were done or wait for me to blow the stock one.

[SixShooter'00Camaro]

Re: Quick little photo shoot for my graduation photos!

and were going to leave the stock rear end in while im building one and eithier swap it in when were done or wait for me to blow the stock one.

It you make it to 500rwhp the rear ends going to explode the first time you go wot.

[ACiFiC]

Re: Quick little photo shoot for my graduation photos!

Well working 40 hours a week or more for about two months should get me the money to finish the turbo build and everything else i want for the car. then i am going to go to either wyotech or uti

And this motor is going to have a huge cam je forged pistons, huge gt45 turbo, built transmission, stall, and i garrenty it willl make over 500hp

40 hours a week is chump hours, doesnt make squat.

[Docta]

Re: Quick little photo shoot for my graduation photos!

Can you guarantee spellcheck?

[bigairboarder44]

Re: Quick little photo shoot for my graduation photos!

I can take a **** in a box and mark it guaranteed. :banana:

[techsan23]

Re: Quick little photo shoot for my graduation photos!

And this motor is going to have a huge cam je forged pistons, huge gt45 turbo, built transmission, stall, and i garrenty it willl make over 500hp

What are the specs on your cam and the compression ratio on the pistons?

[flamingchicken]

Re: Quick little photo shoot for my graduation photos!

What are the specs on your cam and the compression ratio on the pistons?

im not unique, but i can tell you the cam is gonna be HUGE...and the compression ratio, is gonna be like 13.0:1. He's gonna use top of the line head bolts to keep the head from blowing slap off when he hits peak boost. The head gaskets are gonna be coated in trans-x...lol

im kidding.

[Niko97RS]

Re: Quick little photo shoot for my graduation photos!

500HP is possible...guess I was wrong

http://www.camarozone.com/forum/f16/500-hp-v6-478/

[bigairboarder44]

Re: Quick little photo shoot for my graduation photos!

500HP is possible...guess I was wrong

http://www.camarozone.com/forum/f16/500-hp-v6-478/

Yeah, and if you read the thread, you can see that a little bit has been done to it. Like all of the following...

Engine was built by Abbott racing heads.
L32 rods
Diamond Pistons rings and pins
cometic gaskets
ARP Rod Bolts
ARP Main Studs
Comp Cam: 218/218 528/528 114
Comp 918 Valve springs
Comp. Push rods
Titanium retainers
Comp OE lifters
ARP heads studs
Bored
fully ported heads and intakes
Honed
Decked
Installed cam bearings freeze plugs and block balance shaft oil hole
Balance crank rods and pistons
Turn crank
160*
65LB Mototron injectors
SLP MAF
MSD DIS-4 Plus

Custom Turbo from FFF
Custom FWD sweeping headers
Master Power T70 Turbocharger (.7 a/r compressor, p trim turbine, .68 a/r t4)
OBX intercooler 30x12x3
Greddy type S BOV
Turbonetics Deltagate Mark II Wastegate
Greddy Profec B Boost controller
Autometer Gauges

[esoteric18]

Re: Quick little photo shoot for my graduation photos!

Thats actually not too crazy. When i bought my car a few years ago it was 800 bucks with 100k miles. So add all of that your still cheaper then a stock ls1 car.

[flamingchicken]

Re: Quick little photo shoot for my graduation photos!

500HP is possible...guess I was wrong

http://www.camarozone.com/forum/f16/500-hp-v6-478/

thats linx's car. thing had some money into it.

[2.8 Bird]

Re: Quick little photo shoot for my graduation photos!

You really lived up to your screen name, Unique..

Good job on making it unique. How's that turbo working for you?

[esoteric18]

Re: Quick little photo shoot for my graduation photos!

yeah i think he now has 649 to the wheels.

[Unique96Camaro]

Re: Quick little photo shoot for my graduation photos!

You really lived up to your screen name, Unique..

Good job on making it unique. How's that turbo working for you?

Just ordered the turbo and still building the motor.

yeah i think he now has 649 to the wheels.

And did i ever say i would have 681 hp to the wheels NO i said the engine will make around 681 hp. IDK how much it will make to the wheels we will just have to see.