White Faced Gauges, C5 Shift Knob, and Polished Alternator (clear corners, scroll) - FirebirdV6.com/CamaroV6.com Message Board

Announcement

Collapse
No announcement yet.

White Faced Gauges, C5 Shift Knob, and Polished Alternator (clear corners, scroll)

Collapse
X
Collapse
 
  • Page of 2
  • Filter
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • #1

    White Faced Gauges, C5 Shift Knob, and Polished Alternator (clear corners, scroll)

    Ok, so today i finally got around to installing the gauges i got for xmas... here they are

    by the way, the big yellow wire coming out of the back of the headlight switch is the one I tapped into... the one that goes on and off with the headlights... i probably should have taken more time to fine the one that goes on and off with the parking lights... whoops

    http://www.cardomain.com/member_page...56_27_full.jpg

    all lit up...

    http://images.cardomain.com/installs...56_29_full.jpg

    Heres the polished aluminum shift knob i got. its for a c5, but with a little modding i got it to fit. That little piece of paper is laying behind it, its not attached.

    http://images.cardomain.com/installs...56_28_full.jpg

    Heres the polished alternator, this took FOREVER! I just kept sanding and sanding and sanding.... heres the turnout:

    http://images.cardomain.com/installs...56_30_full.jpg

    [ March 15, 2004, 05:15 PM: Message edited by: Loochy88 ]

    96 V6 A4 Camaro and 99 Z28 A4 Camaro     Visit My F-Body Page
    Tags: None
  • #2
    Me likes. [img]graemlins/thumbsup.gif[/img] [img]graemlins/thumbsup.gif[/img]
    <b>Black 1996 3.8L Firebird A4</b><br />--------------------------<br />Custom CAI, Flowmaster Dual Exhaust, 160 Deg Thermo, BMR ShockTower Brace<br />JVC mp3 HU, two 12\" Infinity Kappa Perfects, Infinity 6.5\" components, JBL 600.1 & 80.4 amps <br /><a href=\"http://community.webshots.com/album/479229363CPbPiz\" target=\"_blank\">Pics</a>

    Comment

    • #3
      Where did ya get those white face gauges??!?!?!?!?

      I've been looking everywhere for a white 120mph gauge face!
      1997 Camaro,<br />SLP cold-air, Hooker Supercompetition catback, Air temp. module, Powerstat thermo, 1LE Aluminum drive shaft, 3.42 POSI rear, 1LE sway bars front & rear, Powerstop crossdrilled rotors on all corners, Torque Thrust II\'s (17x9.5 front & 17x11 rear), and a couple other goodies. <a href=\"http://www.villagephotos.com/pubbrowse.asp?selected=84487\" target=\"_blank\">http://www.villagephotos.com/pubbrowse.asp?selected=84487</a>

      Comment

      • #4
        <blockquote>quote:</font><hr>Originally posted by LimitedE:
        Where did ya get those white face gauges??!?!?!?!?

        I've been looking everywhere for a white 120mph gauge face!        <hr></blockquote>

        i got them through a company that sells on ebay, ill see if i can find the name again.... or the auction... hold on...

        96 V6 A4 Camaro and 99 Z28 A4 Camaro         Visit My F-Body Page

        Comment

        • #5
          ok.... heres the ones i bought...

          http://cgi.ebay.com/ws/eBayISAPI.dll...tem=1874569172

          check out some of these links:
          http://cgi.ebay.com/ws/eBayISAPI.dll...tem=1875895092

          http://cgi.ebay.com/ws/eBayISAPI.dll...tem=1875901810

          http://cgi.ebay.com/ws/eBayISAPI.dll...tem=1875966833

          http://cgi.ebay.com/ws/eBayISAPI.dll...tem=1876012444

          96 V6 A4 Camaro and 99 Z28 A4 Camaro           Visit My F-Body Page

          Comment

          • #6
            Looks great Loochy...next spring you have to enter that car in some shows with MOFBA...it looks great.

            Jack
            97 Silver Bird<br />3.8 M5 Bone Stock Engine<br />15.528 @ 88.96 bone stock<br /><a href=\"http://www.fbodyenhancements.com/\" target=\"_blank\">www.fbodyenhancements.com/</a>

            Comment

            • #7
              it would be fun to enter the car in another show. i did one last year. id like to get the front bumper repainted b4 i do that though, its not too horrible, but there are little chips all over it.

              i just put some clear corners on, check them out here:

              http://www.camarov6.com/cgi-bin/ulti...c&f=5&t=003406

              96 V6 A4 Camaro and 99 Z28 A4 Camaro               Visit My F-Body Page

              Comment

              • #8
                is your spedo and tach still correct? i want to get indiglo gagues but i'm scared i won't get the needles back in the right spot. was the install very hard?
                <a href=\"http://www.cardomain.com/id/briansr\" target=\"_blank\">97 White Pontiac Firebird 3.8 A4</a><br />Mods- 2.75\" exhaust, Dynomax muffler, magnaflow cat, SLP CAI, Hypertech 160* thermo, Fan switch<br />Suspension-Kumho Ecsta 712\'s, 32mm/19mm sway bars<br /><br />Our Lady of Blessed Acceleration, don\'t fail us now. <br />-Elwood Blues

                Comment

                • #9
                  yeah, you can put them in the right spot real easy, the speedo is right where it used to be. there are even little screws that hold it in place

                  96 V6 A4 Camaro and 99 Z28 A4 Camaro                   Visit My F-Body Page

                  Comment

                  • #10
                    just go here

                    web page

                    Comment

                    • #11
                      I like those guages, to bad they dont make 'em for 93-96 z28s :(
                      Wolf<br /><a href=\"http://www.cardomain.com/memberpage/249111/7\" target=\"_blank\">95 black t-top camaro</a>,3.4 5 speed,ud pullies,plugs/wires,de-shaft tb & gutted airbox, homemaid short throw shifter

                      Comment

                      • #12
                        hehehe, you polished your Alternator too?..why stop there I did my TB too ;) ..ya your right it does take forever!!...Nice gauges too ;)

                        "Money can't buy me happiness, but I'm happiest when I can buy what I want"
                        05' CTS-V
                        00' Camaro - SOLD :(

                        Comment

                        • #13
                          Nice socks, I have the same. [img]smile.gif[/img]
                          1996 3.8L V6 Camaro A4 Y87<br />Flowmaster 80 Series<br />LPE Cold Air Induction<br />LPE 1 Piece Aluminum Driveshaft<br />BMR Torque Arm<br />Window Tint 5%/5% Sides/Back<p><a href=\"http://members.cardomain.com/adinsx\" target=\"_blank\">http://members.cardomain.com/adinsx</a>

                          Comment

                          • #14
                            I definetly dig the clear corners.

                            BTW, nice car Looch [img]graemlins/thumbsup.gif[/img]
                            1997 Camaro,<br />SLP cold-air, Hooker Supercompetition catback, Air temp. module, Powerstat thermo, 1LE Aluminum drive shaft, 3.42 POSI rear, 1LE sway bars front & rear, Powerstop crossdrilled rotors on all corners, Torque Thrust II\'s (17x9.5 front & 17x11 rear), and a couple other goodies. <a href=\"http://www.villagephotos.com/pubbrowse.asp?selected=84487\" target=\"_blank\">http://www.villagephotos.com/pubbrowse.asp?selected=84487</a>

                            Comment

                            • #15
                              I just got the same gauges....im glad i got them, they look good........were they hard to install...how did u do it?
                              96\' Camaro RS<br />Stock

                              Comment

                              Previous 1 2 template Next

                              Latest Topics

                              Collapse

                              There are no results that meet this criteria.

                              FORUM SPONSORS

                              Collapse
                              Working...
                              X

                              We process personal data about users of our site, through the use of cookies and other technologies, to deliver our services, personalize advertising, and to analyze site activity. We may share certain information about our users with our advertising and analytics partners. For additional details, refer to our Privacy Policy.

                              By clicking "I AGREE" below, you agree to our Privacy Policy and our personal data processing and cookie practices as described therein. You also acknowledge that this forum may be hosted outside your country and you consent to the collection, storage, and processing of your data in the country where this forum is hosted.

                              I Agree