Tweet
I've got some condensation in my fog lights and rear tail lights... can anyone tell me how to get rid of it?
-
-
The tail lights are easy....just remove the lights and put next to a fireplace for 15 minutes. Not too close or they might melt.<a href=\"http://www.onid.orst.edu/~waltejam/\" target=\"_blank\">98 Bright Red Camaro</a><br />Too many mods to list....check my website -
I was blowing fog lights and DRL's so often, I kept extra bulbs in my glovebox. On a drunken whim, I got my trusty DeWalt 18volt drill, a flashlight, and a small drill bit and drilled 4 small holes along the bottom of all 4 lights. I have YET to blow another bulb! As for the rears, I don't know since I don't have that problem. Hope that helps!
<br /><br /> <a href=\"http://www.cardomain.com/id/nitroxxx28\" target=\"_blank\">http://www.cardomain.com/id/nitroxxx28</a>Comment
-
after u put it in a fireplace for 15 min like said above just remember when putting it back to put some crazy glue or another type of glue in the rubber that goes around the tailight so that it would get closer to the tailight that way it wont happen to you again ;o)...Comment
-
silicone maybe?!?!2005 Cavalier LS Sport M5<br /> <a href=\"http://members.cardomain.com/firefighter8615\" target=\"_blank\">http://members.cardomain.com/firefighter8615</a>Comment
-
i have condensation in a fog light and i drilled three holes in the bottom when i replaced the bulb and the bulb was out in less than a week<a href=\"http://www.cardomain.com/memberpage/483076\" target=\"_blank\">http://www.cardomain.com/memberpage/483076</a> <br />TSP rumbler, straight pipe, corvette servo. <br />Soon - 3.42+lsd,headers, cai,Comment
-
My driver's side tail light is cracking around the edges and is starting to get moisture in it. I replaced the bulb in there once already. You'r saying I should put it by the fireplace? For 15minutes? How close?Comment
-
blow dryer.1996 Camaro RS Bright Red<br />3.8L V6 A4 3.42\'s<br />K&N Filtercharger<br />Flowmaster 80 Series Muffler<br />Y87 Performance PackageComment
-
<blockquote>quote:</font><hr>Originally posted by Marquinhos:
after u put it in a fireplace for 15 min like said above just remember when putting it back to put some crazy glue or another type of glue in the rubber that goes around the tailight so that it would get closer to the tailight that way it wont happen to you again ;o)...<hr></blockquote>
NEVER...EVER PUT CYANOACRILITE-BASED GLUE ON A PAINTED PLASTIC PART!!!!!!!! This includes "superglue" "crazy glue" and anything else that says "CA" on the front!!!
The plastic WILL frost and will NOT come off without the help of acetone (ketone..any other abrasive solvent)!!!! Your paint will be ruined, your taillight will be RUINED!
DON'T DO IT!1997 Camaro 30th Anniversary...M5, chrome 16\" 5-stars Goodyear 245/50R16<p><a href=\"http://members.cardomain.com/issycamaroman\" target=\"_blank\">http://members.cardomain.com/issycamaroman</a>Comment
-
Do you have altezza tail lights?
I ask because I have two of the same problems...or did. My fog light is still fogged...but I just don't feel like fixing it yet...I will possibly just swap it because it is a persistent problem.
As for Altezza tail lights, I had a talk with Suncoast Creations last night because I sent my tail lights to them about 3 weeks ago. Apparently they were dealing with a supplier called in pro car parts, that was selling crappy tail lights. I asked how often this happened and they said probably 2/3 out of every ten...which we both agreed weren't very good odds. So I asked for a refund.
If my stock tails fogged...I don't even think I'd be able to see it...
MarkEmail: thehitman5@hotmail.com<br />AIM: DriveDomestic6MT<br />1995 Teal Camaro 3.4L V6 A4<br />Some small modsComment
-
So my truck is finally getting some work done, after 17 years, Oil pressure sensor went out and it’s located under the lower intake manifold. Have to...1 week ago
Comment