Welcome to the FirebirdV6.com/CamaroV6.com forums.
You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!
If you have any problems with the registration process or your account login, please contact contact us.
If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
I may need to install a gauge soon...where are you guys installing them if not on the pillars...I don't like the look of them up there, I want to maintain as much of a factory look as possible. I'm even hesitant about doing the side vent, because even that is a little conspicous, but atleast its a little better then the pillars...
Has anyone put it in the ashtray? or made it be able to flip up from the ashtray so that you could see it when you need to, but hide it when you dont?
Ashtray idea sounds pretty good. I don't know if you've have your console out, but it is a pretty thin plastic and the access in that particular area should be plenty deep enough for a gauge. Or you could mount it a little bit deeper into the cassette holder area.
Ashtray idea sounds pretty good. I don't know if you've have your console out, but it is a pretty thin plastic and the access in that particular area should be plenty deep enough for a gauge. Or you could mount it a little bit deeper into the cassette holder area.
I can't do the cassette holder area because thats where my Gps is...fits perfectly, almost as if they made that spot exactly for it...
I'd like to mount it deep in the ash tray, but I was also thinking about maybe buying one of those single gauge pods like this (but not CF)
and mounting that in the ashtray location...that would make it very visibile, it would actually kind of be set up similar to the gauges on the new camaro I think....Just not sure how it would really look...especially because it will only be a fuel pressure gauge...
ive seen people put a switch fo cut outs in the astray but not a gauge, but that would be pretty cool. maybe put it in the little cubby infront of the shifter?
3M MAFIA ________
| Dynomax Catback | Auburn Posi | 3:42s | B&M Ripper | DIY CAI | PVC Mod |
Next on the list: GT2 Cam| 105# Springs |Headwork| Headers |
sigpic
ive seen people put a switch fo cut outs in the astray but not a gauge, but that would be pretty cool. maybe put it in the little cubby infront of the shifter?
Ha Ha, still gota work on enlarging them, feel free to pass on suggestions. I guess my wife decided it was time I learned since I just went back to school. Anyway I still have to do some clean up work, all I did was use a cheap gauge surround cut it the width of the ashtray, made a couple of cuts in the ashtray and it drops in. I'll make a cover for it when I get time. I spliced the light wire for power and ground then ran the wires to the amp, not necessary but always wanted it.
I use a cheap chrome bezel that came from an autozone autometer knock off gauge, you can use a piece of hard plastic an a key hole saw to make one, I just wanted to see if it would work, good thing it did, lol. I think all single gauges come with the piece I'm talking about. If I figure out how to enlarge the pics. you'll even be able to see and area towards the drive has room for a switch.
Hey everyone! I've been trying to remove my transmission for two days now! I need to replace the clutch. Only thing I've got left holding the transmission...
Hello, so I changed the front bearings on the bird and the ABS inoperative light came on. I made a mistake of not removing negative battery cable. Now...
I usually have to double, triple my headlight switch for them to come up on my 97 Firebird. I cleaned all connections. Could it be the headlight switch...
3 weeks ago
FORUM SPONSORS
Collapse
Working...
X
We process personal data about users of our site, through the use of cookies and other technologies, to deliver our services, personalize advertising, and to analyze site activity. We may share certain information about our users with our advertising and analytics partners. For additional details, refer to our Privacy Policy.
By clicking "I AGREE" below, you agree to our Privacy Policy and our personal data processing and cookie practices as described therein. You also acknowledge that this forum may be hosted outside your country and you consent to the collection, storage, and processing of your data in the country where this forum is hosted.
Tweet
Comment