Alot of people say they havnt seen any results with the hypertech so I was intrested so I went out and ran over 11 times in a 2 hour time period so the weather did not change a whole lot from the beggining to the end. Sorry it was only a 1/8 mile track but hey. I have intake and exhast with 3.42's an lsd and to make sure traction was a big problem I had DR on.
I had gone to the 1/4 mile track the night before but wasnt impressed with the results 14.7's. problem was I only got to make 4 runs that whole night and I kept changing the settings and so it never had time to learn what was going on.
oh and if your wondering 9.2 in the 1/8 is about 14.5 in the 1/4
here are my slips
60' 1/8 mph time of the run notes
2.11 9.45 73.94 5:32
2.12 9.47 74.06 5:37
2.17 9.53 73.98 5:59 hpp3 installed
2.13 9.39 74.61 6:03
2.10 9.28 75.10 6:32
2.09 9.27 74.91 6:39
2.10 9.30 74.99 6:45
2.09 9.28 75.13 6:48
2.10 9.27 75.19 6:54
I set the hpp3 to 93 oct, rev limiter 6300, raised 1-2 shift point by 1 mph (130rpms or so), removed limiter, 50% firmer shifts
when you first install hpp3 it takes a bit for it to learn everything as shown by what I ran. I think alot of people dont give your computer enough time after installing the tunning and also could have traction problems so i made sure I gave it enough time
all of this was done with the maf screen in(its messed up and probably hurt me), with the full belt on, with a wisper lid with no filter(i only had a paper filter with me) and through the catback
I have borla with a high flow cat, whisper lid, LSD with 3.42's and drag radials and some heavy *** KBDD subframes. I didnt even have my ram air installed.
with the progamer I would of ran 14.5X-14.6x with out I was running about a 14.75
ohhh yea 2000 camaro A4
so it was worth an easy tenth or 2 and 1mph
[ February 09, 2004: Message edited by: Drone51 ]</p>
I had gone to the 1/4 mile track the night before but wasnt impressed with the results 14.7's. problem was I only got to make 4 runs that whole night and I kept changing the settings and so it never had time to learn what was going on.
oh and if your wondering 9.2 in the 1/8 is about 14.5 in the 1/4
here are my slips
60' 1/8 mph time of the run notes
2.11 9.45 73.94 5:32
2.12 9.47 74.06 5:37
2.17 9.53 73.98 5:59 hpp3 installed
2.13 9.39 74.61 6:03
2.10 9.28 75.10 6:32
2.09 9.27 74.91 6:39
2.10 9.30 74.99 6:45
2.09 9.28 75.13 6:48
2.10 9.27 75.19 6:54
I set the hpp3 to 93 oct, rev limiter 6300, raised 1-2 shift point by 1 mph (130rpms or so), removed limiter, 50% firmer shifts
when you first install hpp3 it takes a bit for it to learn everything as shown by what I ran. I think alot of people dont give your computer enough time after installing the tunning and also could have traction problems so i made sure I gave it enough time
all of this was done with the maf screen in(its messed up and probably hurt me), with the full belt on, with a wisper lid with no filter(i only had a paper filter with me) and through the catback
I have borla with a high flow cat, whisper lid, LSD with 3.42's and drag radials and some heavy *** KBDD subframes. I didnt even have my ram air installed.
with the progamer I would of ran 14.5X-14.6x with out I was running about a 14.75
ohhh yea 2000 camaro A4
so it was worth an easy tenth or 2 and 1mph
[ February 09, 2004: Message edited by: Drone51 ]</p>
Comment