Welcome to the FirebirdV6.com/CamaroV6.com forums.
You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!
If you have any problems with the registration process or your account login, please contact contact us.
If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
so i changed my brake pads(all 4) what a pain in the ***, about a month ago cuz the old ones were squeeking, now the new ones have started squeeking, not all the time but the majority of the time i apply the brakes....its ****ing annoying and pisses me off..............any suggestions?
appreciation
\"there are things known, and things unknown, and inbetween are the doors\"-jim morrison<br /><br /> <a href=\"http://www.cardomain.com/id/99NBMCamaro\" target=\"_blank\">http://www.cardomain.com/id/99NBMCamaro</a>
\"there are things known, and things unknown, and inbetween are the doors\"-jim morrison<br /><br /> <a href=\"http://www.cardomain.com/id/99NBMCamaro\" target=\"_blank\">http://www.cardomain.com/id/99NBMCamaro</a>
mos tthe sqeuking is the rubbinf of the back of the metal pad against the inside of the caliper.
-Eric<br /><a href=\"http://www.cardomain.com/id/mustangeater82\" target=\"_blank\">2000 NBM V6 Camaro 5-speed</a> T-top <i>converted</i><br /><b>14.467@95.45mph</b> <i>$0 in mods</i><br /><i>The member formerly known as MustangEater8251</i>
did you use high temp grease on the ends of the brake pads where they meet the spacers? did you change out the old spacers with new ones that come with the pads? did you clean the disks with brake cleaner? did you keep the new brake pads clean while installing?
shouldn't have to use any grease or chemical on the pads themselves. just clean everything and use the high temp grease on the contact points of the pad metal backs. check out a haynes manual of the instructions that come with the pads. you will see what i mean.
also grease the spacer bolts. (under the rubber boots.) if those bolts are old and worn you may need new ones. if they bind then the brakes can't adjust well and the pads will have trouble adjusting and making 'flat' contact with rotor.
if you blead the brakes and got fluid everywhere then again...clean with brake cleaner.
Hey everyone! I've been trying to remove my transmission for two days now! I need to replace the clutch. Only thing I've got left holding the transmission...
Hello, so I changed the front bearings on the bird and the ABS inoperative light came on. I made a mistake of not removing negative battery cable. Now...
I usually have to double, triple my headlight switch for them to come up on my 97 Firebird. I cleaned all connections. Could it be the headlight switch...
3 weeks ago
FORUM SPONSORS
Collapse
Working...
X
We process personal data about users of our site, through the use of cookies and other technologies, to deliver our services, personalize advertising, and to analyze site activity. We may share certain information about our users with our advertising and analytics partners. For additional details, refer to our Privacy Policy.
By clicking "I AGREE" below, you agree to our Privacy Policy and our personal data processing and cookie practices as described therein. You also acknowledge that this forum may be hosted outside your country and you consent to the collection, storage, and processing of your data in the country where this forum is hosted.
Tweet
****ing brakes
Comment