Tweet
Most of you know my mods, most boltons/ powerpack/cam etc. etc. i have 26lb ls1 injectors and the walbro in tank pump, are these injectors to much?is it possible they would slow me down at all from being to much? thanks for any help guys.
-
Longtubes, true duals, ram air, caspers tps tec, ls1 26lb injectors, supersix powerpack, heads milled .020, comp cam .507 220/224 114 ls, forged internals and chromeoly pushrods, bored .030 over, tb spacer, tranny built with stiffer springs and kevlar bands, bigger servo, transgo stage 3 shift kit, edge 3600 stall, 1 pc aluminum ds, 3.73 superior gears, lsd rear ,custom pcm tuning, walbro 255 in tank, -
That will definitely be too much for a V6. You will want to go with an injector under 24 lbs or lower if you are not going with forced induction or nitrous.- Josh<br />If you have any questions or need installation pics/help, e-mail me: Viper98885@aol.com<br /><a href=\"http://Camaroz28.cardomain.com/id/viper98885\" target=\"_blank\">\'93 Camaro Hardtop</a><br /><a href=\"http://Camaroz28.cardomain.com/id/01lincolnls8\" target=\"_blank\">\'01 Lincoln LS8 Sport</a><br />\'00 Yamaha YZF-R6<br /><a href=\"http://www.ftpp.net\" target=\"_blank\">Full Throttle Performance</a> -
well john d said that if my pcm is programmed for them they wont slow me down or hurt performanceLongtubes, true duals, ram air, caspers tps tec, ls1 26lb injectors, supersix powerpack, heads milled .020, comp cam .507 220/224 114 ls, forged internals and chromeoly pushrods, bored .030 over, tb spacer, tranny built with stiffer springs and kevlar bands, bigger servo, transgo stage 3 shift kit, edge 3600 stall, 1 pc aluminum ds, 3.73 superior gears, lsd rear ,custom pcm tuning, walbro 255 in tank,Comment
-
That's a lot of fuel to be dumping into a NA V6. Custom computer programming will be a must with injectors that size.- Josh<br />If you have any questions or need installation pics/help, e-mail me: Viper98885@aol.com<br /><a href=\"http://Camaroz28.cardomain.com/id/viper98885\" target=\"_blank\">\'93 Camaro Hardtop</a><br /><a href=\"http://Camaroz28.cardomain.com/id/01lincolnls8\" target=\"_blank\">\'01 Lincoln LS8 Sport</a><br />\'00 Yamaha YZF-R6<br /><a href=\"http://www.ftpp.net\" target=\"_blank\">Full Throttle Performance</a>Comment
-
You would be more than fine with smaller injectors.- Josh<br />If you have any questions or need installation pics/help, e-mail me: Viper98885@aol.com<br /><a href=\"http://Camaroz28.cardomain.com/id/viper98885\" target=\"_blank\">\'93 Camaro Hardtop</a><br /><a href=\"http://Camaroz28.cardomain.com/id/01lincolnls8\" target=\"_blank\">\'01 Lincoln LS8 Sport</a><br />\'00 Yamaha YZF-R6<br /><a href=\"http://www.ftpp.net\" target=\"_blank\">Full Throttle Performance</a>Comment
-
viper you have mail please respondLongtubes, true duals, ram air, caspers tps tec, ls1 26lb injectors, supersix powerpack, heads milled .020, comp cam .507 220/224 114 ls, forged internals and chromeoly pushrods, bored .030 over, tb spacer, tranny built with stiffer springs and kevlar bands, bigger servo, transgo stage 3 shift kit, edge 3600 stall, 1 pc aluminum ds, 3.73 superior gears, lsd rear ,custom pcm tuning, walbro 255 in tank,Comment
-
Wht is stock in our 3.8's, and how small can we go?
-MarcsigpicComment
-
<blockquote>quote:</font><hr>Originally posted by hockeyman:
Wht is stock in our 3.8's, and how small can we go?
-Marc<hr></blockquote>
19 lbs, should be 21 lbs.
From a link in the Engine Tech Database:
http://www.rceng.com/technical.htmRobert - owner www.FirebirdV6.com/CamaroV6.com
"Mid-life crisis? I'm way beyond that!"
1996 Black Firebird GTxxxRam Air V6 w/ M5xxxwww.FirebirdGT.com
RavenComment
-
<blockquote>quote:</font><hr>Originally posted by FirebirdGT:
19 lbs, should be 21 lbs.
From a link in the Engine Tech Database:
http://www.rceng.com/technical.htm<hr></blockquote>
Thank You!
-MarcsigpicComment
-
The worst that would happen with larger injectors is a rough idle. But unless you have large amounts of HP you won't need more than 24lb injectors.<a href=\"http://www.onid.orst.edu/~waltejam/\" target=\"_blank\">98 Bright Red Camaro</a><br />Too many mods to list....check my websiteComment
-
<blockquote>quote:</font><hr>Originally posted by speedy-v6-camaro:
The worst that would happen with larger injectors is a rough idle. But unless you have large amounts of HP you won't need more than 24lb injectors.<hr></blockquote>
The other consideration is the range of adjustment that the pcm can handle. I've heard it's around 25%. My fuel trim runs about 20% with the 24 lb injectors. (if I don't tweak the base setting on my maft, which is another whole discussion in itself...) So 26 lb and up injectors could exceed the pcm's adaptive capabilities.
If you exceed the range, then you'll run rich all the time, not just at idle, which will be bad for power, mileage, and durability.\'98 A4 Camaro v6->v8 conversion, and STS kit next<br />v6: 13.6 Powerdyne, 13.2 150 shot, 13.8 120 shot, 14.3 85 shot, 15.7 stock<br />v8(na): 12.18@113, 392rwhp<br />Moderator on <a href=\"http://www.mtfba.org\" target=\"_blank\">www.mtfba.org</a> and <a href=\"http://www.frrax.com\" target=\"_blank\">www.frrax.com</a> (Road Race & Autocross)<br /><a href=\"http://community.webshots.com/user/johnduncan10\" target=\"_blank\">Car pics</a>, <a href=\"http://www.trscca.com\" target=\"_blank\">TN Region SCCA</a>Comment
-
now if i get my pcm programmed for the 26lbers i shouldnt run rich correct?Longtubes, true duals, ram air, caspers tps tec, ls1 26lb injectors, supersix powerpack, heads milled .020, comp cam .507 220/224 114 ls, forged internals and chromeoly pushrods, bored .030 over, tb spacer, tranny built with stiffer springs and kevlar bands, bigger servo, transgo stage 3 shift kit, edge 3600 stall, 1 pc aluminum ds, 3.73 superior gears, lsd rear ,custom pcm tuning, walbro 255 in tank,Comment
-
<blockquote>quote:</font><hr>Originally posted by SLOWBRAEATER:
now if i get my pcm programmed for the 26lbers i shouldnt run rich correct?<hr></blockquote>
Yep, you should be ok, if they remap the fuel table, then the pcm will be dead on. Then it won't be having to try to adapt to an injector it's not programmed for.\'98 A4 Camaro v6->v8 conversion, and STS kit next<br />v6: 13.6 Powerdyne, 13.2 150 shot, 13.8 120 shot, 14.3 85 shot, 15.7 stock<br />v8(na): 12.18@113, 392rwhp<br />Moderator on <a href=\"http://www.mtfba.org\" target=\"_blank\">www.mtfba.org</a> and <a href=\"http://www.frrax.com\" target=\"_blank\">www.frrax.com</a> (Road Race & Autocross)<br /><a href=\"http://community.webshots.com/user/johnduncan10\" target=\"_blank\">Car pics</a>, <a href=\"http://www.trscca.com\" target=\"_blank\">TN Region SCCA</a>Comment
-
With a mini-AFC or a PCM recal you can run any size injectors you want and be ok.Comment
-
thanks zooomer and everyone else [img]graemlins/thumbsup.gif[/img]Longtubes, true duals, ram air, caspers tps tec, ls1 26lb injectors, supersix powerpack, heads milled .020, comp cam .507 220/224 114 ls, forged internals and chromeoly pushrods, bored .030 over, tb spacer, tranny built with stiffer springs and kevlar bands, bigger servo, transgo stage 3 shift kit, edge 3600 stall, 1 pc aluminum ds, 3.73 superior gears, lsd rear ,custom pcm tuning, walbro 255 in tank,Comment
-
Hey everyone! I've been trying to remove my transmission for two days now! I need to replace the clutch. Only thing I've got left holding the transmission...4 weeks ago
Comment