H4351 conversion kit question

[3.4 slow to go]

Looks like I have (maybe) a Eurolamps kit, w/the whole headlight assy swapped, not just a 9005/6 conversion. The h4351 lamp burnt out. Does anyone know if eurolamps sell just replacement bulbs? Just wondering before I shoot them an e-mail asking the same.

Or does anyone else know of just a vendor selling the bulb itself???

thanks

[3.4 slow to go]

Re: H4351 conversion kit question

here are some pics of what I'm talking about:

housing pic 1




housing pic 2




h9006 h4351 h9005 the h4351 buld is significantly longer than the other two




the clips/tangs of the h4351 (inner clips) on left and that of the h9005/6 (outer clips) right



also, on the housing is a stamp saying:
H4351 12V
D15 M07 2001

[TealV6]

Re: H4351 conversion kit question

Ok.. now I remember.. those are just Autozone replacements. SEALED replacements! http://www.amazon.com/Sylvania-H4351.../dp/B000COB8BE

[TealV6]

Re: H4351 conversion kit question

Also.. this is for those that need a FULL list of EVERY bulb on the camaro. (this should fit all first rev, 4th gen camaros)

1994 CHEVROLET Camaro

Low beam headlamp
H4351

High beam headlamp
H4352

Parking light
2397

Front turn signal
2397

Rear turn signal
2057
2057LL Long Life Upgrade: Up to twice the life of the standard lamp

Tail light
194
194LL Long Life Upgrade: Up to twice the life of the standard lamp
2057
2057LL Long Life Upgrade: Up to twice the life of the standard lamp

Stop light
2057
2057LL Long Life Upgrade: Up to twice the life of the standard lamp

High mount stop light
921
921LL Long Life Upgrade: Up to twice the life of the standard lamp

Fog/Driving light
885

License plate
194
194LL Long Life Upgrade: Up to twice the life of the standard lamp

Back up light
1141
1141LL Long Life Upgrade: Up to twice the life of the standard lamp

Front sidemarker
194
194LL Long Life Upgrade: Up to twice the life of the standard lamp

Rear sidemarker
194
194LL Long Life Upgrade: Up to twice the life of the standard lamp

Ash tray
194
194LL Long Life Upgrade: Up to twice the life of the standard lamp

Glove box
194
194LL Long Life Upgrade: Up to twice the life of the standard lamp

Map light
212-2

Dome light
906

Step/Courtesy light
562
74

Trunk/Cargo area
562

Under hood light
93

Instrument-general
161
194
194LL Long Life Upgrade: Up to twice the life of the standard lamp
37

Check engine indicator
161

Hi-beam indicator
161

Seat belt indicator
161

Brake warning
161

Automatic transmission indicator
73

Directional signal indicator
161

[3.4 slow to go]

Re: H4351 conversion kit question

sealed beams w/composite style bulbs?

I guess I'll reckon on fixin on moseying on over there & have a look-see

edit: high beams have the composite setup too

edit2: these are also different housing connectors than the eurolamp style

[TealV6]

Re: H4351 conversion kit question

Also in txt format for your ipod... that's where I keep both this and the one for my Jeep. :)

[3.4 slow to go]

Re: H4351 conversion kit question

went to AZ to look at the stock replacements, and, well,,,,




never heard of a "sealed beam" light w/removable bulb. Then what are the really old style lights called then


anywho, I just gonna trim the outside edge of the 9006 lights I have sitting around & rtv those suckers in.

Learn something new everyday.

[viper98885]

Re: H4351 conversion kit question

You can heat up the housing of the stock bulbs which will allow you to remove the stock bulb from the housing. It will soften the glue and you can get it out. Then, clean out the rest of the sealant from the surrounding glass. Out stock lights use the same connector as a 9006 bulb. From there, you can put a 9006 bulb back in the housing using RTV sealant to hold it in. Make sure that it is fully seated and sealed to prevent moisture from leaking in. Put the whole assembly in a vice while wrapped in foam or towels and allow RTV to seal. This will allow you to choose what bulbs you want in there from now on (PIAA, Silverstars, etc.) and replacements are MUCH cheaper.

[3.4 slow to go]

Re: H4351 conversion kit question

the drivers side was easy, didn't have to heat anything up, just cleaned it out, trimmed teh edges of te 9006 bulb & applied the rtv. about 2hrs later, applied some more as insurance. The pass side was a diff brand, and I jsut went ahead & applied liberal use of a dremel tool & cut it, cleaned it up, countersunk the connector top & then hit it w/rtv twice also. I'll worry about the highbeams after I get a new high beam switch installed.