Tweet
Oil Pan
To Replace the oil pan what do you have to do exactly .. i have a 3.4 M5 and my friend who is suppose to do it says it will take longer than a week to do .. he said he has to drop the front end suspension? Why ? Who knows exactly what you have to do? it doesn't have to be in detail just sumthing i could work off
-
-
Re: Oil Pan
1) buy a haynes or chiltons
disconnect battery
raise the front of the vehicle
place squarely on jack stands
e-brake it
drain oil
remove crossover pipe / hanger bolts
remove the driveplate/flywheel cover and starter
remove hood
remove the wiring harness clip from the left side of the pan
disconnect the wires from the oil level sensor then the sensor
support the engine from above with a hoist
remove engine mount through bolts
carefully remove the pan2k2 camaro, K&N, SLP whisper lid, Konis, AEM, HP Tuners, Angel eyes/Halos, CF SS ram air hood, 4.10s, Zexel Torsen, UMI SFCs, CrossFire, BFGs, Gatorback, Catco, Flows, and TLC! DONT feed the Trolls! -
Re: Oil Pan
Do you have to drop the front end suspension? in any way?Comment
-
Re: Oil Pan
doesn't mention it in the manual. so, doubtful that it is needed.Comment
-
Re: Oil Pan
lift the engine2k2 camaro, K&N, SLP whisper lid, Konis, AEM, HP Tuners, Angel eyes/Halos, CF SS ram air hood, 4.10s, Zexel Torsen, UMI SFCs, CrossFire, BFGs, Gatorback, Catco, Flows, and TLC! DONT feed the Trolls!Comment
-
Re: Oil Pan
Why??Comment
-
Re: Oil Pan
clearacne between the pan bolts and the k-mbr1978 Formula 461 in progress of being built :rock:
2013 Ram 1500 Big Horn
former owner of 85 bird w/ 2.8 - 3.4 - 3800 II - 5.0
94 comero 3.4Comment
-
Re: Oil Pan
Clearacne???Originally posted by 3.4 slow to goComment
-
Re: Oil Pan
http://google.com
http://dictionary.com
http://wikipedia.com
clearance = gap
I said you have to lift the engine... so to make a Gap, so you have Room to pull the oil pan off. (the K-member is in the way)2k2 camaro, K&N, SLP whisper lid, Konis, AEM, HP Tuners, Angel eyes/Halos, CF SS ram air hood, 4.10s, Zexel Torsen, UMI SFCs, CrossFire, BFGs, Gatorback, Catco, Flows, and TLC! DONT feed the Trolls!Comment
-
Re: Oil Pan
yes, clearance. k-member sits really close to the pan and you need to lift the engine to create more space. yes, clearance.Comment
-
Re: Oil Pan
you coudl drop the front suspension and kmember to do it, but from the looks of it, its just easier ot lift the motor.Comment
-
Re: Oil Pan
hey i just put my pan on, lift the motor then as you drop the pan you have to turn it as it is falling. turng counter clock wise. once you get the pan past the cross member, turn it stright and tilt the right side up. that will clear the oil pick up tube.Comment
-
Re: Oil Pan
Ok so i found what i was lookin for lol I appreciate it thanx guys again i was see whether front suspension would have to be dropped or the motor would have to be liftedComment
-
Re: Oil Pan
i did a combination of both when i did my 3.8, it was a huge pitaComment
-
Re: Oil Pan
Anyone ever try using HT sealant around the pan to stop any gasket leaks, instead of replacing the gasket?Robert - owner www.FirebirdV6.com/CamaroV6.com
"Mid-life crisis? I'm way beyond that!"
1996 Black Firebird GTxxxRam Air V6 w/ M5xxxwww.FirebirdGT.com
RavenComment
-
Hey everyone! I've been trying to remove my transmission for two days now! I need to replace the clutch. Only thing I've got left holding the transmission...2 weeks ago -
Hello, so I changed the front bearings on the bird and the ABS inoperative light came on. I made a mistake of not removing negative battery cable. Now...3 weeks ago -
I usually have to double, triple my headlight switch for them to come up on my 97 Firebird. I cleaned all connections. Could it be the headlight switch...3 weeks ago
Comment