Share your header preference.

[FirebirdGT]

Re: Share your header preference.

Do you just have a small warehouse of spare parts? lol.. and do those not fit on 00-02 then?

My wife thinks I turning the garage into one. 2-1/2 cars, extra deep and too small! LOL

And two salvage yards within 15 minutes with a 95 3.4 Bird, and Camaros - 93 V8, 96 V6, 00 V6, & 02 V6. I spend about 1-2 hours each Sat morning stripping parts. :rock:

Any 95-99 headers will fit a 00-02. Only the CIA are 00-02 specific due to the interference with the AC on the 95-99 cars. But they too will work if the AC line is moved.
.

[Docta]

Re: Share your header preference.

Lucky you... None of the salvage yards near me have a Camaro/Firebird at all. But back on topic, what're the advantages of LT's over shorties?

[Rhunadan]

Re: Share your header preference.

I have OBX Racing stainless headers - but still in the box.

It appears that they are no longer on the OBX site - just eBay - probably discontinued.
.

Those look great. Please let us know how they fit. Can't beat the price.

[Rhunadan]

Re: Share your header preference.

Never mind. I couldn't wait for the review. I just ordered a set:D

[ACiFiC]

Re: Share your header preference.

Is your car stock height or lowered? I'm dropping it 1.8" and wasn't sure the long tubes wouldn't scrape on the ground going over a bump or something.

what springs?

[Rhunadan]

Re: Share your header preference.

Eibach Sportlines or B&G's , haven't made up my mind yet.

[ACiFiC]

Re: Share your header preference.

Eibach Sportlines or B&G's , haven't made up my mind yet.

I didnt think those would give you the almost 2'' drop

[FirebirdGT]

Re: Share your header preference.

Never mind. I couldn't wait for the review. I just ordered a set:D

http://forum.camarov6.com/showthread...ght=obx&page=2

.

[CFreed11]

Re: Share your header preference.

My OBX headers will hipefully be going on this weekend. I'm planning on using this extended weekend to try and get whole exgaust done, and I'll finish up my thread with an update afterwards..

[Rhunadan]

Re: Share your header preference.

I didnt think those would give you the almost 2'' drop

They advertise a 1.8" drop for the Eibachs and 1.6" for the B&G's. I guess its not exactly a 2" drop, but close enough for me. I wanted the SLP springs, but they're only good for an inch .

[unvmyrs]

Re: Share your header preference.

To the op... correct me if I read you wrong... but if you have turbo you cannot use headers unless they are turbo headers. Especially longtubes because they'll look like spaghetti noodles. Im no expert on boosted cars though.

[bigairboarder44]

Re: Share your header preference.

To the op... correct me if I read you wrong... but if you have turbo you cannot use headers unless they are turbo headers. Especially longtubes because they'll look like spaghetti noodles. Im no expert on boosted cars though.

You can use whatever kind of manifold/header you want. It's just the fitment issue that has everyone going with turbo headers or manifolds.

Though I could be incorrect also :)

[Pewter02Camaro]

Re: Share your header preference.

Im gonna take a stab in the dark and say hes going to be or already runs a blower.....

[Rhunadan]

Re: Share your header preference.

I'm modifying an M90 blower, so header design is not an issue.

[WarShrike]

Re: Share your header preference.

Might look at Strano springs as well. They have a good spring rate and are a great handling spring FWIW.

I run the FFF LT's and love them. I dented mine once because I wasn't paying attention to where I was while leaving a parking lot in low light (now fixed).

I never scrape my longtubes and I'm a little lower than stock but that's because I'll bottom out if I lower my car much more as our streets are terrible.