Tweet
Here is my setup for my 1994 3.4 camaro. Pacestter headers and y-pipe, to 3inch in/out catco cat,3inchspipe, to flowmaster 80's series 3 inch exhaust dual outlet. Now my problem is that I need a shop to put the exhaust from the cat back on at least. Due to the welds that need to be put on. This would save me a lot of money because they would not install the headers. However, the y-pipe is 2.5 inch where the cat is 3inches. Is there something I can tell the exhaust shop to do, so I can install the headers later that wont require any welding. Also if some people could give me what they paid for a cat to the tips to be put on, that would be helpful. Also if someone paid for an entire install from headers back. The tips are already welded on to the muffler, the over axle pipe is cut off from the muffler.
-
My Car <a href=\"http://members.cardomain.com/tucsoncamaro\" target=\"_blank\">http://members.cardomain.com/tucsoncamaro</a> <br />3 inch flowmaster catback system, with ceramic coated pacesetter headers,3 inch cat,K&N FIPK -
2.5 inch y pipe? gayness, I think the exhaust shop that you go to can figure out something for that, if not you need to find an 2.5 inch in 3 inch out cat.\'99 SSM Camaro V6 M5<br />(mod list on cardomain site; too long to list here)<br /> <a href=\"http://www.cardomain.com/id/v6cam99\" target=\"_blank\">http://www.cardomain.com/id/v6cam99</a> -
pacesetter y pipe = 3"<a href=\"http://www.onid.orst.edu/~waltejam/\" target=\"_blank\">98 Bright Red Camaro</a><br />Too many mods to list....check my websiteComment
-
maybe for the 3.8, but not the 3.4My Car <a href=\"http://members.cardomain.com/tucsoncamaro\" target=\"_blank\">http://members.cardomain.com/tucsoncamaro</a> <br />3 inch flowmaster catback system, with ceramic coated pacesetter headers,3 inch cat,K&N FIPKComment
-
yeah I got the same problem and was getting ready to post about itOriginally posted by tucsoncamaro:
maybe for the 3.8, but not the 3.495 Firebird<br /> <a href=\"http://www.cardomain.com/memberpage/673250\" target=\"_blank\">http://www.cardomain.com/memberpage/673250</a> <br /> <a href=\"http://photobucket.com/albums/y217/andrewbrandon19/\" target=\"_blank\">http://photobucket.com/albums/y217/andrewbrandon19/</a> <br /><br />me on a good day------> <a href=\"http://communicatio.webblogg.se/images/wet_cat_113159625.jpg\" target=\"_blank\">linky</a>Comment
-
what is the inlet size of the stock y pipe to the cat? i have a 3'' cat welded to my stock y pipe. any good exhaust shop can make it fit.94 Firebird - Red A4<br /> <a href=\"http://members.cardomain.com/predatorbird\" target=\"_blank\">http://members.cardomain.com/predatorbird</a>Comment
-
So my truck is finally getting some work done, after 17 years, Oil pressure sensor went out and it’s located under the lower intake manifold. Have to...2 hours ago -
Hey guys. For starters I’ve always been a big car guy, I love all types of cars and can appreciate all types of engineering. I’ve always been a Chevy...2 weeks ago -
Getting a message saying invalid interface, haven’t used it since last year probably November. First time in 23 years I had a problem. Going to get...2 weeks ago
-
-
need help finding a balancer and a replacement balancer bolt. im at a lost after confusing myself researching.3 weeks ago
Comment