I just bought my cut off for my firebird and i live in cali theres no where to go to get it put on..is there anybody that lives in cali that knows where i could go?
Announcement
Collapse
No announcement yet.
Where can i go to get my cut off put on?
Collapse
X
-
Where can i go to get my cut off put on?
1995 3.4L Camillion Firebird<p>Mods: flowmaster,Custom 3inch cutout,Moroso Air intake,2000 firebird rear lights(really makes a diff),fog lights,B&M Quick shifter,Custom Automatic short shifter handle,<p>Upcomming Mods:Pulleys,3 inch Cat,Power chip,headers,gears.. WHICH = ALOT OF MONEY....Tags: None
-
Whats a cut off?1993 3.4 <br />Borla rear section<br />3 inch Catco High Flow Cat<br />2.75 inch I pipe (Picked one up from an LT-1 guy for a whole $10)<br />K&N Fipk <br />180° T-stat<br />Jet Stage II<br />10 Spoke Z28 Wheels<br />NGK\'s, Taylor Spiros<br />Mobil 1 synthetic<p>Email Viper2@chesnet.net for 4th gen replacement parts.
-
any place that does exhaust stuff should be able too.New Car: 2004 GTP Comp G (Test Vehicle) 13.936@99.32 <br />Mods: Cylinder Filter,No Mufflers, 3.3\" <br />Old Car: 2000 Formula 13.124 @ 106.01 with 2.73\'s<br />Other Car: 1993 Firebird 16.1@83
Comment
-
i still have it all stock from the headers and the cat.. will it be worth it to still put the cut out on? i got flow masters but my car starts off loud but then gets quite.. i need it loud all the time..1995 3.4L Camillion Firebird<p>Mods: flowmaster,Custom 3inch cutout,Moroso Air intake,2000 firebird rear lights(really makes a diff),fog lights,B&M Quick shifter,Custom Automatic short shifter handle,<p>Upcomming Mods:Pulleys,3 inch Cat,Power chip,headers,gears.. WHICH = ALOT OF MONEY....
Comment
-
Yes it'll be worth it to put the cutout on. It makes it really loud and deep. I have the same setup... stock pipes/cat/headers, with a flowmaster 80 muffler, and a cutout along my i-pipe.
Any muffler shop, even in California, should install it without problems. If they hassle you, just tell them that it's for racing use at a dragstrip only, and you don't plan on using it on the street (even if you do).Kyle M<br />--------------<br /><a href=\"http://grdws6.netfirms.com\" target=\"_blank\">2002 Trans Am WS6</a> (silver, A4) - lid, cutout, stage 3 shift kit, 12 bolt, vig 3200, tranny cooler, bmr sfc/stb, torq thrust ii. <b>12.688 @ 106.47mph -=- 1.756 60\'</b>
Comment
-
do u just run it open or close on the street? and have u ever got pulled over by the police with it being that loud? [img]graemlins/omg.gif[/img]1995 3.4L Camillion Firebird<p>Mods: flowmaster,Custom 3inch cutout,Moroso Air intake,2000 firebird rear lights(really makes a diff),fog lights,B&M Quick shifter,Custom Automatic short shifter handle,<p>Upcomming Mods:Pulleys,3 inch Cat,Power chip,headers,gears.. WHICH = ALOT OF MONEY....
Comment
-
Could you get into trouble for running it with the cut out open on the street? Is there like a law against it. I personally have never heard a cut out in person but people tell me it is very loud. I am planning on getting one within the next 2 weeks. I don't think it could be louder than some of those fudging HARLEYS!<a href=\"http://www.saintsworth.com/z06\" target=\"_blank\">\'02 Corvette Z06</a>
Comment
-
i think u can get pulled over for it being to loud it just depends on if the cop thinks he is a noise hero.. cause where i live they always looking at my car and im still stock well a little bit over stock.. :D1995 3.4L Camillion Firebird<p>Mods: flowmaster,Custom 3inch cutout,Moroso Air intake,2000 firebird rear lights(really makes a diff),fog lights,B&M Quick shifter,Custom Automatic short shifter handle,<p>Upcomming Mods:Pulleys,3 inch Cat,Power chip,headers,gears.. WHICH = ALOT OF MONEY....
Comment
-
I honestly doubt you'll get pulled over. Sure, it's loud... but it's not OVERLY loud... well, I guess... yesterday I was goin over to my gf's, and she said she could hear me coming from around the corner while she was in her room, and I was almost idling...
Still though, there's plenty of people out there with exhaust that's much louder then what a cutout will make yours. Legally, I'm not sure if a cutout is illegal to use on the streets or not... I'm pretty sure that a muffler is a required device, isn't it? But technically, if your cutout is opened, your muffler is still in use :D But still, it's not loud enough that you hafta worry about getting pulled over.... probably.Kyle M<br />--------------<br /><a href=\"http://grdws6.netfirms.com\" target=\"_blank\">2002 Trans Am WS6</a> (silver, A4) - lid, cutout, stage 3 shift kit, 12 bolt, vig 3200, tranny cooler, bmr sfc/stb, torq thrust ii. <b>12.688 @ 106.47mph -=- 1.756 60\'</b>
Comment
-
what is the best kind to get cause i got mine from a shop but i think they make theres... whats the best cutout to get?1995 3.4L Camillion Firebird<p>Mods: flowmaster,Custom 3inch cutout,Moroso Air intake,2000 firebird rear lights(really makes a diff),fog lights,B&M Quick shifter,Custom Automatic short shifter handle,<p>Upcomming Mods:Pulleys,3 inch Cat,Power chip,headers,gears.. WHICH = ALOT OF MONEY....
Comment
-
I hear that the Flowtech is the best one. Just don't get JcWhitney one. People tell me its horrible and it leaks :( So stick with flowtech thats what I'm ordering next monday [img]smile.gif[/img]<a href=\"http://www.saintsworth.com/z06\" target=\"_blank\">\'02 Corvette Z06</a>
Comment
-
Yeah, go with FlowTech. If you still have stock piping, you should get a 2.25" cutout, and www.quicktimeperformance.com is the only site I've ever seen that sells a 2.25" FlowTech cutout. All others just sell 2.5 and 3". www.summitracing.com also sells their own cutouts, which are the same design, and a little cheaper. No 2.25" though.Kyle M<br />--------------<br /><a href=\"http://grdws6.netfirms.com\" target=\"_blank\">2002 Trans Am WS6</a> (silver, A4) - lid, cutout, stage 3 shift kit, 12 bolt, vig 3200, tranny cooler, bmr sfc/stb, torq thrust ii. <b>12.688 @ 106.47mph -=- 1.756 60\'</b>
Comment
Latest Topics
Collapse
-
Hey guys. For starters I’ve always been a big car guy, I love all types of cars and can appreciate all types of engineering. I’ve always been a Chevy...2 weeks ago
-
by ssms5411Getting a message saying invalid interface, haven’t used it since last year probably November. First time in 23 years I had a problem. Going to get...2 weeks ago
-
need help finding a balancer and a replacement balancer bolt. im at a lost after confusing myself researching.3 weeks ago
-
Hello every one, ozzy here ive been looking at this page for weeks now finally joined. So my question is why is it that every turbo build forum just ends...3 weeks ago
Comment