I just bought my cut off for my firebird and i live in cali theres no where to go to get it put on..is there anybody that lives in cali that knows where i could go?
Announcement
Collapse
No announcement yet.
Where can i go to get my cut off put on?
Collapse
X
-
Where can i go to get my cut off put on?
1995 3.4L Camillion Firebird<p>Mods: flowmaster,Custom 3inch cutout,Moroso Air intake,2000 firebird rear lights(really makes a diff),fog lights,B&M Quick shifter,Custom Automatic short shifter handle,<p>Upcomming Mods:Pulleys,3 inch Cat,Power chip,headers,gears.. WHICH = ALOT OF MONEY....Tags: None
-
Whats a cut off?1993 3.4 <br />Borla rear section<br />3 inch Catco High Flow Cat<br />2.75 inch I pipe (Picked one up from an LT-1 guy for a whole $10)<br />K&N Fipk <br />180° T-stat<br />Jet Stage II<br />10 Spoke Z28 Wheels<br />NGK\'s, Taylor Spiros<br />Mobil 1 synthetic<p>Email Viper2@chesnet.net for 4th gen replacement parts.
-
any place that does exhaust stuff should be able too.New Car: 2004 GTP Comp G (Test Vehicle) 13.936@99.32 <br />Mods: Cylinder Filter,No Mufflers, 3.3\" <br />Old Car: 2000 Formula 13.124 @ 106.01 with 2.73\'s<br />Other Car: 1993 Firebird 16.1@83
Comment
-
i still have it all stock from the headers and the cat.. will it be worth it to still put the cut out on? i got flow masters but my car starts off loud but then gets quite.. i need it loud all the time..1995 3.4L Camillion Firebird<p>Mods: flowmaster,Custom 3inch cutout,Moroso Air intake,2000 firebird rear lights(really makes a diff),fog lights,B&M Quick shifter,Custom Automatic short shifter handle,<p>Upcomming Mods:Pulleys,3 inch Cat,Power chip,headers,gears.. WHICH = ALOT OF MONEY....
Comment
-
Yes it'll be worth it to put the cutout on. It makes it really loud and deep. I have the same setup... stock pipes/cat/headers, with a flowmaster 80 muffler, and a cutout along my i-pipe.
Any muffler shop, even in California, should install it without problems. If they hassle you, just tell them that it's for racing use at a dragstrip only, and you don't plan on using it on the street (even if you do).Kyle M<br />--------------<br /><a href=\"http://grdws6.netfirms.com\" target=\"_blank\">2002 Trans Am WS6</a> (silver, A4) - lid, cutout, stage 3 shift kit, 12 bolt, vig 3200, tranny cooler, bmr sfc/stb, torq thrust ii. <b>12.688 @ 106.47mph -=- 1.756 60\'</b>
Comment
-
do u just run it open or close on the street? and have u ever got pulled over by the police with it being that loud? [img]graemlins/omg.gif[/img]1995 3.4L Camillion Firebird<p>Mods: flowmaster,Custom 3inch cutout,Moroso Air intake,2000 firebird rear lights(really makes a diff),fog lights,B&M Quick shifter,Custom Automatic short shifter handle,<p>Upcomming Mods:Pulleys,3 inch Cat,Power chip,headers,gears.. WHICH = ALOT OF MONEY....
Comment
-
Could you get into trouble for running it with the cut out open on the street? Is there like a law against it. I personally have never heard a cut out in person but people tell me it is very loud. I am planning on getting one within the next 2 weeks. I don't think it could be louder than some of those fudging HARLEYS!<a href=\"http://www.saintsworth.com/z06\" target=\"_blank\">\'02 Corvette Z06</a>
Comment
-
i think u can get pulled over for it being to loud it just depends on if the cop thinks he is a noise hero.. cause where i live they always looking at my car and im still stock well a little bit over stock.. :D1995 3.4L Camillion Firebird<p>Mods: flowmaster,Custom 3inch cutout,Moroso Air intake,2000 firebird rear lights(really makes a diff),fog lights,B&M Quick shifter,Custom Automatic short shifter handle,<p>Upcomming Mods:Pulleys,3 inch Cat,Power chip,headers,gears.. WHICH = ALOT OF MONEY....
Comment
-
I honestly doubt you'll get pulled over. Sure, it's loud... but it's not OVERLY loud... well, I guess... yesterday I was goin over to my gf's, and she said she could hear me coming from around the corner while she was in her room, and I was almost idling...
Still though, there's plenty of people out there with exhaust that's much louder then what a cutout will make yours. Legally, I'm not sure if a cutout is illegal to use on the streets or not... I'm pretty sure that a muffler is a required device, isn't it? But technically, if your cutout is opened, your muffler is still in use :D But still, it's not loud enough that you hafta worry about getting pulled over.... probably.Kyle M<br />--------------<br /><a href=\"http://grdws6.netfirms.com\" target=\"_blank\">2002 Trans Am WS6</a> (silver, A4) - lid, cutout, stage 3 shift kit, 12 bolt, vig 3200, tranny cooler, bmr sfc/stb, torq thrust ii. <b>12.688 @ 106.47mph -=- 1.756 60\'</b>
Comment
-
what is the best kind to get cause i got mine from a shop but i think they make theres... whats the best cutout to get?1995 3.4L Camillion Firebird<p>Mods: flowmaster,Custom 3inch cutout,Moroso Air intake,2000 firebird rear lights(really makes a diff),fog lights,B&M Quick shifter,Custom Automatic short shifter handle,<p>Upcomming Mods:Pulleys,3 inch Cat,Power chip,headers,gears.. WHICH = ALOT OF MONEY....
Comment
-
I hear that the Flowtech is the best one. Just don't get JcWhitney one. People tell me its horrible and it leaks :( So stick with flowtech thats what I'm ordering next monday [img]smile.gif[/img]<a href=\"http://www.saintsworth.com/z06\" target=\"_blank\">\'02 Corvette Z06</a>
Comment
-
Yeah, go with FlowTech. If you still have stock piping, you should get a 2.25" cutout, and www.quicktimeperformance.com is the only site I've ever seen that sells a 2.25" FlowTech cutout. All others just sell 2.5 and 3". www.summitracing.com also sells their own cutouts, which are the same design, and a little cheaper. No 2.25" though.Kyle M<br />--------------<br /><a href=\"http://grdws6.netfirms.com\" target=\"_blank\">2002 Trans Am WS6</a> (silver, A4) - lid, cutout, stage 3 shift kit, 12 bolt, vig 3200, tranny cooler, bmr sfc/stb, torq thrust ii. <b>12.688 @ 106.47mph -=- 1.756 60\'</b>
Comment
Latest Topics
Collapse
-
by ssms5411So my truck is finally getting some work done, after 17 years, Oil pressure sensor went out and it’s located under the lower intake manifold. Have to...2 hours ago
-
Hey guys. For starters I’ve always been a big car guy, I love all types of cars and can appreciate all types of engineering. I’ve always been a Chevy...2 weeks ago
-
by ssms5411Getting a message saying invalid interface, haven’t used it since last year probably November. First time in 23 years I had a problem. Going to get...2 weeks ago
-
need help finding a balancer and a replacement balancer bolt. im at a lost after confusing myself researching.3 weeks ago
Comment