need help fast(i am hookingit up now)

[southern94]

i am hooking up the a/f gauge and fuel pressure gauge and i have some ???'s

i started to unscrew the shrader valve to T in the sending unit and the fpss and gas started seeping out is that just because of pressure or what? will it stop? i closed it back quickly

here is a pic of my 02 sensorwhere do i piggy pack into? i heard it is supposed to be to a purple wire but don't see one

www.members.aol.com/hitithard67/camaropics/02.jpg

[ January 19, 2002: Message edited by: southern94 ]</p>

[Magnus]

It will stop eventually. Do this.

Uncrew the gas cap to relieve pressure.

Unplug the fuel pump... near the back drier side tire in about a foot are 2 connections that plug into the body.. just disconnect both of them.

Then start the car till it runs out of gas (shouldn't take long).

Wait 20 seconds and start it again.

There should now be minimal pressure in the lines.

[southern94]

i got the scrader valved off and the valve is 1/8 i think and so i have to go find a nipple for my 1/4 T to fit it dangit.

i still need help with the o2 i need to know where to hook in to for the a/f gauge i got the dual pod in and i got the gauges in i am thinking about taking pics and doing a install guide but i need some help with o2 sensor

[12secondv6]

Yup magnus is right, it will stop.
As for the wire, yes it is the purple wire.
I spliced it into the o2 sensor in front of the cat.

[southern94]

i got the vavle prob fixed just fine but i still can not find that damn purple ire i was looking at the o2 sensor there is one wire that runs out of the top into a loom???
what is the deal?

[12secondv6]

Do 94's have a non heated o2 sensor?
This is my only guess on this
How many wires do you see for that 02 sensor?

[southern94]

i only see one wire coming out of the top of the 02 on each side of the intake i have a pic but i can not get the dern link to work

[12secondv6]

Do you have a helms or chilton manual?
or that link would be great

[southern94]

i am trying to get it to work i need to know how to hook this up i want to finish it tom :rolleyes:

www.members.aol.com/hitithard67/camaropics.sensor.jpg

[ January 19, 2002: Message edited by: southern94 ]</p>

[12secondv6]

it said can't find page???

[southern94]

can i email you the pic ??

i need your email address

[southern94]

12sec you have mail with the pic attatched

[12secondv6]

I'm at work and I can't give out the e mail address.
They watch all that is incoming and outgoing and they freak out if it is non mercedes stuff.
Send it to my reg e mail address.
james12secv6@aol.com
I am going out tonight though so either much later tonight r first thing in the morning I'll send an answer

[94-3.4]

94's do NOT have heated o2 sensors. Also, there is a o2 and each of the manifolds and not one on the ypipe or around the cat. Therefore it would make it difficult to tap into both of the 02 sensors for a reading.

[southern94]

i am trying to splice into the wire on the manifolds do i just piggy back into the one wire coming out of the top of the sensor do i have to do it on both sensors? if so i can and connect those two wires to a singal wire running to the gauge little help here

THE LINK WORKS NOW!!

www.members.aol.com:/hitithard67/camaropics/sensor.jpg

also what power source should i hook it up to i was thinking that a fuse might not have enough to push it i will try

[ January 19, 2002: Message edited by: southern94 ]</p>