OBDII Port - please help - FirebirdV6.com/CamaroV6.com Message Board

Announcement

Collapse
No announcement yet.

OBDII Port - please help

Collapse
X
Collapse
 
  • Page of 1
  • Filter
  • Time
  • Show
Clear All
new posts
Previous template Next
  • #1

    OBDII Port - please help

    OK, so I am trying to connect HP Tuners to the OBDII port and it keeps saying that the car isnt giving power to the tuning unit.

    I checked the fuse and it seemed fine, I swapped it out with another 25amp fuse just to check and same thing.

    Is the port bad?/? Any help would be great
    SLP CAI, RK Sport headers, P&Ped heads and intake, GT2 cam, Upgraded valvetrain, Z28 rear axle with 4.10s Tx Spd tune, Z06 rims, 2.5\" exhaust to flowmaster, 160* thermo, B&M ripper, upgraded ignition, rockford fosgate 12\" with sony xplode amp and HU.
    Tags: None
  • #2
    Re: OBDII Port - please help

    Make sure that all of your fuses are good, and also make sure that the contacts are clean on the port, and no wires are disconnected or damaged behind the port.

    Also, your key needs to be in the 'on' position.
    Representin' Team Red In The North

    Red '96 Pontiac Firebird "Smokeshow" 3800, M5, Far From Stock!!

    Black/Red '89 Jeep Cherokee "Tigerclaw" Chev 327, Turbo 400... Stock What??

    Black/Red '02 Honda CBR 954RR Fireblade

    Comment

    • #3
      Re: OBDII Port - please help

      yea be sure the key is to the run position, meaning the heater works and the dash lights are on
      1997 Camaro LS1 RS
      1994 Camaro - Sold
      1999 Trans am Vert - Sold

      A Few Mods....

      Comment

      • #4
        Re: OBDII Port - please help

        thats a check, car is in the on position and I checked the fuse over again. the cig lighter works so I know its not the fuse. I guess I gotta inspect the wires behind it and see whats up.
        SLP CAI, RK Sport headers, P&Ped heads and intake, GT2 cam, Upgraded valvetrain, Z28 rear axle with 4.10s Tx Spd tune, Z06 rims, 2.5\" exhaust to flowmaster, 160* thermo, B&M ripper, upgraded ignition, rockford fosgate 12\" with sony xplode amp and HU.

        Comment

        • #5
          Re: OBDII Port - please help

          Ok I am getting very frustrated.

          I had a keyless entry installed last summer. Do u think he may have crossed some lines?

          I am at a loss......so much for installing my turbo just to find out I can hookup my car to get tuned.
          SLP CAI, RK Sport headers, P&Ped heads and intake, GT2 cam, Upgraded valvetrain, Z28 rear axle with 4.10s Tx Spd tune, Z06 rims, 2.5\" exhaust to flowmaster, 160* thermo, B&M ripper, upgraded ignition, rockford fosgate 12\" with sony xplode amp and HU.

          Comment

          • #6
            Re: OBDII Port - please help

            have you gotten hptuners to hook up to another car?



            (alot of people with older version had problems with USB--->Serial adapters not working with HPtuners, only a few did)

            Comment

            • #7
              Re: OBDII Port - please help

              try hooking something else up to your obdII, see if its hptuners. try autozone and tell them you want a code read.

              96 V6 A4 Camaro and 99 Z28 A4 Camaro               Visit My F-Body Page

              Comment

              • #8
                Re: OBDII Port - please help

                I tried HP Tuners on my roomates car and it worked. I think something is F'ed up with the jack itself.

                I dont know what else it could be
                SLP CAI, RK Sport headers, P&Ped heads and intake, GT2 cam, Upgraded valvetrain, Z28 rear axle with 4.10s Tx Spd tune, Z06 rims, 2.5\" exhaust to flowmaster, 160* thermo, B&M ripper, upgraded ignition, rockford fosgate 12\" with sony xplode amp and HU.

                Comment

                Previous template Next

                Latest Topics

                Collapse
                • Andy H
                  Transmission removal help!!
                  by Andy H
                  Hey everyone! I've been trying to remove my transmission for two days now! I need to replace the clutch. Only thing I've got left holding the transmission...
                  2 weeks ago
                • 2.8 Bird
                  Abs inop
                  by 2.8 Bird
                  Hello, so I changed the front bearings on the bird and the ABS inoperative light came on. I made a mistake of not removing negative battery cable. Now...
                  3 weeks ago
                • fishin
                  Intermittent Headlight Function 97 Firebird
                  by fishin
                  I usually have to double, triple my headlight switch for them to come up on my 97 Firebird. I cleaned all connections. Could it be the headlight switch...
                  3 weeks ago
                View All

                FORUM SPONSORS

                Collapse
                Working...
                X

                We process personal data about users of our site, through the use of cookies and other technologies, to deliver our services, personalize advertising, and to analyze site activity. We may share certain information about our users with our advertising and analytics partners. For additional details, refer to our Privacy Policy.

                By clicking "I AGREE" below, you agree to our Privacy Policy and our personal data processing and cookie practices as described therein. You also acknowledge that this forum may be hosted outside your country and you consent to the collection, storage, and processing of your data in the country where this forum is hosted.

                I Agree